Paint!

With all the repairs made it was time to prepare the hull for paint. The existing finish was flatted down and dings and bad scrapes filled. In keeping with my usual practice a coat of primer was applied, followed by further filling and fairing.

I think I've mentioned this before, but I don't consider myself to be a great painter. I used a close cell foam roller to get the first gloss coat of Blakes Enamel on (decided to go with good old white in the end...). This went OK, but there was no way was it going to be a 'mirror' finish. I decided to apply the next coat the same way but 'laying it off' with a brush in the recommended manner. Hmmm, maybe a slight improvement - but I think the use of the roller for the previous coat had produced too much in the way of orange peel. To be honest, it's not a bad finish and would probably look quite acceptable when polished up.

However, I've decided as there is never going to be a better opportunity than now to see if I can improve on it, I'm going to flat down everything above the waterline with wet or dry and then I'll have another go using the 'laying off' procedure - let's hope the weather stays OK...

I'll keep you posted!

Over she goes...

With the help of some of the local 'muscle', we carried the boat out of the (ahem) 'boat-shed' and rolled her over - using some pontoon fenders to cushion the blow (thanks Tony...) - it was then carried back in to the shed and placed on the same fenders, the front benefiting from the addition of a judiciously placed milk crate.

This was the first opportunity to inspect the hull/keel in detail. Remember the hull was said to be 'in good condition'? Well, apart from a very suspicious repair it didn't appear too bad - just the usual scrapes and dings that are to be expected for a neglected vessel of the 70's. The repair was to the keel and consisted of a couple of sheets of chopped strand mat (CSM) laid over the paintwork and soaked in resin. A little gentle persuasion with a screwdriver and the whole lot just broke away revealing... a hole! There was also evidence of a previous, but much more substantial (and correctly executed) repair.

As I have said elsewhere, these boats were constructed with a sealed 'buoyancy' tank, making access to the interior of the hull impossible without opening an access point through the floor. I had made this even more difficult by adding a further wooden floor - hey ho...

So there I was, an upside down Broom with a hole and no easy way to access the hull internally. An evening trawling around the net threw up a couple of useful articles about patching a hull from the outside and I decided to have a go at this option. To cut a long story short, the hole was opened up to ease access and the surrounding area chamfered down to produce a 'dish', everything was then cleaned with acetone. Luckily, the structure was dry - if there were any moisture it would have to have been dried out completely before work could start. I made a patch consisting of layers of glass cloth and CSM, this was soaked with resin as was the hole. I threaded some old bootlaces(!) through the patch and introduced the whole thing through the hole, using the bootlaces to pull it up and manoeuvre it into place. When it had almost 'set off' I started building up layers of CSM, each overlapping the last and also including a strengthening layer of glass cloth. Finally, the whole area was overlaid with a fine glass 'tissue'. I tried to get the contours as close as possible - but a little light filling was inevitable, again this was done just prior to the whole lot setting off - in order to provide a chemical bond between all the components (well that's what I've been told).

With the repair complete, it was sanded down and a light coat of primer rolled over it to reveal imperfections. A little further sanding and filling and the job was done.

The patched area is now clean and smooth and the repair appears to have been highly successful.

The moral of this story is to check that hull/keel for bodged repairs. It's only taken a paragraph or so to write this up but it was a couple of days of hard graft to get the thing properly repaired and seaworthy!

Planning Ahead

Remember those Bow-rail supports? Well they're all finished and the rails themselves were given a dose of steel wool and elbow grease. Couldn't resist balancing them in place to get an idea of how things will look:

...and while we're still dreaming of the future, heres a small sample of the Teak and Holly Laminate that will be used to cover the foredeck:

Hopefully we'll find a matching Teak only version for the sidedecks. At the moment the plan is to finish her in Blakes Pearl White, with a stripe (as per the original) in 'Bordeaux'. The plan is to fit out the inside in White, Grey and Bordeaux with a few highly varnished burr walnut veneered panels for the dashboard area.

Tents and Topsides...

The English summer continues and over the past few weeks the most effort has gone into pumping out collected rainwater and debris hurled at the Broom blown from the trees by the high winds. Outdoor boatbuilding has its drawbacks - something had to be done.

Trawling ebay turned up the perfect solution - a party tent! Although the driveway now looks as if we are hosting a small wedding reception at least work can carry on whatever the weather as the Broom has its own 'boat-shed'. The tent is pretty substantial and since its erection has guaranteed that there has been no rain and unbroken sunshine. One bright spark did point out that it cost more than the boat though...

The first job in the new boat-shed was to finish tidying up the transom well. This required some cosmetic filling, sanding, filling etc. Finally, a 'reveal' coat of Blakes white primer, followed by more detail filling and a light sanding. There will be more work in this area as fittings for the engine and steering control cables will need to be made along with the stainless strengthening plate referred to in a previous post.

The (almost) completed transom well
and the slide in cover that will hide the fuel/battery etc.

The rest of the 'topsides' have also undergone a similar treatment.

It'll look worse before it looks better - Don't be disheartened!

Plenty of sanding, detail filling and the use of fingertips to detect any rough areas - and it's ready for a primer/reveal coat.
Finally, following a wash down and a wipe over with thinners and a tack cloth, (the boat, not me...) the paint is applied. I have to admit I'm no great shakes with a brush and have found I get the best results from a close cell foam roller - these are also cheap and 'chuckable' (hands up all those that enjoy cleaning brushes). When this first coat of primer is applied it makes all the tedious preparation worthwhile - it's beginning to look like a boat!

Topsides in primer

Apart from the odd small job, work is now going to stop on the topsides. The plan is to slide the boat out, flip it over, carry it back in to the 'shed' and carefully place it on milk-crates / car-tyres / whatever... in order that work can start on the hull (and I bet that won't be as simple as it sounds).
Rummaging around on the ground I've already discovered a small - but not very well done - patch in the hull - let's hope there's nothing too nasty under there.
The plan is to complete the hull entirely - right down to final finish, flip the boat back over, place it on a cradle and complete the topsides and fit out - simple. When this is finally done, the overcoating times for the topsides primer will have been exceeded, but this will be lightly rubbed down and a futher coat applied. I'll keep you posted!